Only registered users can write reviews. You can also disengage the winder mechanism and have it operate as a normal plunge router. The MOF001 KC includes a lot of stuff. For real delicate work I would be using either the included offset base or one of One more size/height comparison, again both collets set at the same height.One problem I noticed which is fixed easily is the depth stop turret. The next video (at right) I installed the extended baseplate, fence set to cut about 2" in from the edge and a 1/2" straight bit. I had top side dust collection going with the hose connected to the left side of the router. The Triton's cord was not long enough by itself to be used without causing a tripping hazard. In a piece of pine I cut a stopped dado. The last issue I had was with the soft start. Single dial switch from plunge to fixed-base router with rack and pinion height adjustment.Award-winning router with compact and powerful 1400W / 2-1/4hp motor and 8000-21,000rpm electronic speed maintenance under load. Of course nothing is dust free but this attachment did a remarkable job of collecting the waste. Page 9 4.
It does take some getting used to. I've heard of people complaining that when mounted in a table and using a remote power switch is gets in the way but that just isn't an issue in my opinion. Please refer to our policy terms and conditions listed below.Customer must contact us (in-store, phone, or email) to inform one of our customer service representatives of the particular item, its lower price, and the retailer selling the item, before they place their order.If customer doesn’t see the competitor’s lower price until after they purchased the exact, in-stock item from us, then that customer has 30 days to notify us so that we can issue a refund for the amount of the price difference.BIS reserves the right to verify the price and the availability of the item (i.e. For table mounting, the MOF001 has quick-fit pins located in the base, allowing rapid fitment to the mounting plate, making it more than capable of performing in the Triton RTA300 router … The difference was so small and in my opinion inconsequential that after performing this testing I have to assert that the performance of the Triton's soft start is virtually on par with that of the Milwaukee. TRA … Variable speed ensures the router will handle a wide variety of bits for exact shaping of material.
The old binding of the fine adjustment problem which some early Triton routers experienced when mounted in the table is not apparent with the new MOF001. The kit includes the Router, above table crank, wench, 1/2" and 1/4" self releasing collets, 7 guide bushings and associated adapters including a PC bushing adapter, offset base with built in circle cutting guide, fence, top and bottom dust collectors, a 1/2" straight bit and instruction manuals. Perhaps it is because in normal use the router is plunged and that brings the handles down considerably lower.The pic at right has both the Triton and the Milwaukee set with the collets at the same height and you can see that while the handles are higher, the Triton is actually just a bit shorter. All of this fits securely in the case.Variable Speed with soft start and continuous speed control under loadDuring the next set of descriptions you can refer to these photos for location information. Easy-set, direct reading 3-stage turret for precise pre-set cut depths. The sleeve gets inserted into the nut and snaps into place. The nylon bodied turret is attached to the base with a sheet metal screw. 3. Compatible with the Triton RTA300 router … To install the router in the table you'll need a hole layout which is the same as for the PC 7518.
1. Compatible with the Triton RTA300 router table. Size wise the MOF001 is quite a bit smaller than the 3-1/4hp TRC001.
Now loosen the collet some more until it gets tight and then loose again. Award-winning router with compact and powerful 1400W / 2-1/4hp motor and 8000-21,000rpm electronic speed maintenance under load. Replace the plunge spring • While this product was designed for efficient and cap and re-tighten the convenient operation on most router tables, it is screw. Award-winning router with compact and powerful 1400W / 2-1/4hp motor and 8000-21,000rpm electronic speed maintenance under load. Because I'm positioning myself so the camera gets a good shot of the router, my stance is a bit out of balance and thus so are my motions. All Rights Reserved. I my opinion this is a great safety feature and has no negative affects. It was of no surprise to me that the MOF001 exhibited the greatest startup torque, however what was surprising was that is was only slightly greater than the Milwaukee.
My initial impression was that the soft start just wasn't all that soft. I alternated between the Milwaukee and the Triton over and over again. What I do to all my routers is shown in these two pictures.